At present, geothermal heating technology has been widely used in home decoration. Due to its advantages such as comfort and convenience, it has developed rapidly. However, what kind of floor is suitable for geothermal heating and what are the key issues for installing geothermal floor? Different flooring suppliers from different brands have different opinions and cause consumers to be confused. According to reports, there are three key technologies for installing geothermal floors. First, ground technology processing. Mainly to remove the moisture from the cement floor. If the moisture in the cement floor is not removed before the floor is installed, once heated, a certain amount of moisture shock waves will be generated, which is the main reason for the cracking of the floor. Second, floor installation technology. In order to ensure the installation quality of the geothermal floor, there is a strict set of installation standards for installation of geothermal floors. The installation environment, installation time and installation process are strictly required to ensure the overall quality of the geothermal floor. Third, strict accessories requirements. There is one key detail of the geothermal floor, which is the floor mat of the geothermal floor. The deformation of the floor mat can drive the deformation of the floor. With pvc foam mats, one is slow in thermal conductivity, and the second is prolonged heating and aging. If geothermal floor special floor mats are used, one is that the heat conduction is fast, the second is environmental protection, and the third is no deformation. In addition, when the consumer uses the geothermal heating system in the second year, it must be heated in stages and gradually increase the temperature. Do not adjust the temperature to the highest one at a time. This can easily cause floor damage. The installation of geothermal floor is best to use laminate flooring, because the relative thermal conductivity of the laminate flooring is better, and the solid wood flooring is not easily deformed after being heated; in addition, the product is relatively thin, the general thickness is 8mm, heat conduction is fast, and energy is saved. Geothermal heating has no special technical requirements for strengthening the floor. As long as it is a qualified floor, it can be used as a geothermal floor. Geothermal floor installation with stress: 1. The moisture barrier is required: Geothermal floor pavement requires a layer of moisture-proof membrane to be laid between the floor mat and the ground. This moisture-proof membrane can prevent the evaporation of geothermal heat and damage the floor after evaporating the surface moisture. There may be a lot of manufacturers in order to save a little cost at the expense of reducing the installation requirements, causing great installation risks to the geothermal floor. 2. Careful selection of floor mats: At present, some manufacturers use paper floor mats or aluminum foil floor mats as geothermal heating floor mats. Both of these mats have obvious defects in geothermal heat and directly result in damage to the floor quality. Under the erosive effect of hot evaporation of moisture for a long time, the paper floor mat will gradually rot and lose the moisture resistance of the floor mat so as to damage the floor. The use of aluminum foil floor mats will seriously affect the thermal efficiency. Geothermal heating does not involve convection, so the heat of the geothermal system is achieved through conduction and radiation. However, the aluminum foil on the aluminum foil mat will reflect heat back to the ground, causing the heat radiation to fail to reach the indoor, affecting the heating effect. It also wastes energy. 3, the installation process is particular about: floor installation is not standardized, may cause a variety of quality reasons, such as: uneven floor pavement will cause floor deformation. Therefore, it is recommended that consumers choose good brands. Flooring Considerations Nature Flooring Cement Interior Decor Home Improvement
Powder carbon is Huahui Company's third series of products. Acid washed carbon is Huahui Company's fourth series of products. Through acid washing, alkali washing and special technologies, Huahui can produce < 3% ultra low ash activated carbon.The common produced varieties are 30x200mesh, 60x200mesh, 100x200mesh, <200mesh, <325mesh etc.
Acid Powder Activated Carbon,made from anthracte
Because of its powder state, better diffusivity, it can full touch to the reaction material. Meantime, it is applying to disposable recovery treatment of filling water and industrial waste water with its high efficient adsorption, moreover, also used for refining and decolorization of liquid. The types we manufacture through the year include HF-30x200, HF-60X200,HF-100X200,HF-325 etc.
Anthracite Acid Washed Powder Carbon Anthracite Acid Washed Powder Carbon,Acid Washed Anthracite Powder Carbon,<200Mesh Acid Washed Anthracite Pac,60X200Mesh Acid Washed Anthracite Pac,Anthracite Acid Washed Pellet Activated Carbon Ningxia Huahui Activated Carbon Company Limited , http://www.huahurcarbon-tr.com
coal, which is grinded into suitable powder size with qualified activated carbon,is the third main products of HuaHui Company.