The Cable laying machines over two pairs of propelled pulleys. Two counter pulleys press the cable into the grooves of the two driving pulleys. The cable pusher tapered pulleys consist of a special high elastic and wear resistant rubber material, thus Cable Laying Equipment ensuring adequate friction.
Cable Conveyor Crawler,Power Cable Conveyor,Conveyor Cable,Cable Tube Conveyor NINGBO MARSHINE POWER TECHNOLOGY CO., LTD. , http://www.marshine-power.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge> "Motorcycle bearing" protection method makes it look new The "motorcycle bearing" protection method makes it look new
After the motorcycle engine is differentiated; firstly, the degree of yaw of the crankshaft should be checked: the crankshaft is supported by the V-ring; the yaw degree is measured by the dial gauge; the operating limit of the yaw of the crankshaft is 0. 05 mm; The limit of use. Excessive yaw of the crankshaft is usually the main cause of abnormal engine oscillation; this oscillation will shorten the engine life; reduce the operating time. Therefore, once the operating limit is exceeded, the repair part will be corrected or replaced immediately. /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
Secondly, check the motorcycle bearings: check the front end; first remove the bearing with the solvent to remove the bearing; and smooth with the oil. Then change the inner seat to see if the transition is smooth; if the transition is found to be insensitive and uneven; The impact of "Kada, Kada"; further look at the ball track and steel ball. If the steel ball and the seat are found to have severe pitting, peeling, breaking, etc., it is necessary to replace the new bearing. If the bearing changes very much Normal and smooth; there is no obstruction of the appearance; but the noise of “哗哗†is very large; it is necessary to check whether it can show the appearance of excessive wear. The method of viewing is: hold the inner and outer rings tightly with both hands; push the bearing forward and backward; The gap that feels shaking is very large; it is necessary to replace the new bearing. Then we need to check the oil seal of the bearing; if the appearance of wear, breakage, and hardening is found; such oil seal damage may cause leakage of fuel and air mixture or oil. The oil seal should be replaced immediately.
Again, look at the big-head bearing of the motorcycle connecting rod: view the time; change the crankshaft with the connecting rod; should be able to feel the rotation in the big head change smoothly. Then firmly fix the crankshaft on one side; pull the connecting rod on one side; Acknowledge whether the sound can be expressed in the big head. The degree of wear of the big end of the connecting rod can be estimated by looking at the swing of the small end of the connecting rod; this method can also see the degree of wear of the large part of the connecting rod. The degree of wear cannot exceed 3. 0mm; Wear exceeds this limit; the connecting rod, crank pin and crank pin bearing are all repaired or replaced.
Recommend to friends comments close window Bearing related knowledge Two major layouts of slewing bearings
Estimation of the fatigue life of SKF bearings The specific analysis of the radial ball bearings is the working principle of the sliding bearings?
This article links to http://
Please indicate China Bearing Network http://
Previous:The inspection of NTN imported bearings in the operation of the next section: support three-step composite stamping die depicting
The hydraulic power Cable Blowing Machine pack is connected with the pusher BKS 400 by two hydraulic hoses; the operation cable pusher can be easy managed from the ground, also if the pusher is fixed in a tray.
The hydraulic drive Cable Laying Equipment of the BKS 400 can be operated by a separate power pack or by another machine like an excavator, if the below listed parameters can be provided. The connecting hoses between the BKS 400 and the power pack are equipped with a flow divider, which guarantees the infinitely variable adjusting of speed.
Source: Bearing network time: 2013-10-24