4 Product level and marking 4.1 Product level products are classified into ordinary protection level and high protection level according to their anti-theft capability.
The equipment used to expand vermiculite in industry is called Vermiculite Expansion Furnace. According to the different fuels used, vermiculite expansion furnaces can be divided into natural gas vermiculite expansion furnaces and gas vermiculite expansion furnaces. Before the raw vermiculite expands into the Vermiculite Plant, it needs to be preheated and dried the water percent below 5% . Our company's Vermiculite Expansion Equipment can expand raw vermiculite to tens of times the original volume. Expanded Vermiculite can be mixed into compound fertilizer to increase crop yield, and can also be used as thermal insulation material.
Vermiculite Expansion Furnace Bulk Vermiculite,Vermiculite Expansion Furnace,Vermiculte Producing Furnace,Expanded Vermiculite For Horticulture Henan Dianyan New EnergyTechnology Co. Ltd , https://www.cngasifier.com
4.1.1 General protection level The mechanical anti-theft lock of general protection level shall comply with the relevant provisions in 5.1.6, 5.3, 5.6.2, 5.6.4, 6.4, 5.8. Represented by the letter "A".
4.1.2 High protection level Mechanical anti-theft locks with high protection level shall comply with the relevant provisions in Articles 5.1.6, 5.3, 5.6.3, 5.6.4, and 5.8. Represented by the letter "B".
4.2 Product code mark The product code mark is as follows:
FDS-A or B- ××××
FDS—Anti-theft lock B—High protection level A— Ordinary protection level ×××× —Manufacturer's product model Example FDS-B-MDS MDS type advanced protection level anti-theft lock FDS-A-3S90Ⅱ3S90Ⅱ type general protection level anti-theft lock
5 Technical requirements 5.1 Design requirements 5.1.1 Mechanical anti-theft locks for doors that are opened with a key should not have the function of unlocking the main tongue (bolt) without passing the key. When using a two-way lock, the keys are opened inside and outside Should be the same.
5.1.2 The mechanical anti-theft lock of the billiard structure shall be equipped with not less than 4 special-shaped billets.
5.1.3 After the key is inserted into the lock, when the main lock tongue (bolt) has been extended but has not reached the locked state, the key should not be pulled out of the lock.
5.1.4 The mechanical anti-theft lock opened with a key shall not have a single-row pin structure, but may be a multi-row pin structure, magnetic pin structure, blade structure, lever structure or single-row compound structure.
5.1.5 When the handle or handle of the main lock tongue (bolt) transmission device is damaged by external force, it should be detached from the lock body structurally. At this time, the main bolt (bolt) is still in the locked state.
5.1.6 The extension length of the main tongue (bolt) of the door mechanical anti-theft lock, the mechanical anti-theft lock of class A should not be less than 14mm, and the mechanical anti-theft lock of class B should not be less than 20mm.
5.1.7 The body of the lock body should generally be made of not less than 2mm thick steel plate or other equivalent materials. The folded edges and openings should be welded or stamped integrally. The key parts corresponding to the main lock tongue (bolt) transmission device and the lock body shall have anti-drill protection measures.
5.1.8 All kinds of springs used in the lock should have requirements for elastic use. Under normal conditions of use, the working life should not be less than 6 × 104.
5.1.9 Generally, the lock box (board) should be made of steel plate with a thickness of not less than 2mm or other equivalent materials. The connection to the door frame should be in the form of welding. When using screws to connect the frame, the connection strength should meet the anti-pry Shockproof requirements.
5.1.10 The password of the mechanical code lock should be easy for the user to change, and the procedure for changing the code should be simple and reliable, with good confidentiality.
5.2 Strength requirements 5.2.1 The key is inserted into the middle of the lock. Under the action of 3Nm torque, the key should be free of obvious deformation and damage.
5.2.2 The main bolt (bolt) of the mortise type anti-theft lock and mechanical combination lock withstands 9800N axial static pressure, and the main bolt (bolt) of the external anti-theft lock withstands 3000N axial static pressure. ) The amount of retraction should not be greater than 8mm.
5.2.3 After the main tongue (bolt) of the ferrule type, externally mounted anti-theft lock and mechanical combination lock is subjected to 6000N lateral static pressure, the lock shall be able to be used normally.
5.2.4 When the opening direction of the hook-shaped tongue is subjected to 9000N static pressure, the amount of expansion and contraction of the hook tongue shall not be greater than 1/10 of the original extension.
5.2.5 When the claw-shaped tongue is subjected to a static tension of 12000N in the locked state, the deformation of the claw should not lose the locking function.
5.2.6 The lock box should be able to withstand 9000N static pressure without significant plastic deformation.
5.2.7 After the fixed connection screw hole on the lock head is subjected to 2940N static pressure, there shall be no slipping of the teeth.
5.2.8 The connection between the loose-fit lock and the lock body should be firm and reliable. Under the action of 2940N static tension, the lock should not be separated from the lock body.
5.2.9 The handle, handle, mechanical dial lock dial, and rotating mandrel of the mechanical anti-theft lock are under 2200N tension and 200Nm torque. The handle, handle, dial, rotating mandrel, and transmission device should be There is no damage, deformation and dislocation.
5.2.10 The protective shell of the mechanical combination lock should not produce plastic deformation and cracks under the static pressure of 35000N.
5.3 Anti-vandalism function The mechanical anti-theft lock is installed normally. Use the test tools specified in 6.1 to carry out anti-drill, anti-saw, anti-pry, anti-pull, anti-impact and anti-technical opening tests on the mechanical anti-theft lock. The net working time should not be less than the requirements in Table 1.
Table 1 Anti-vandalism net working time min
5.4 Mechanical combination lock 5.4.1 The parts of the mechanical combination lock should be made of brass, bronze, stainless steel or equivalent materials with corrosion protection and protective coating.
5.4.2 The minimum gap between the two adjacent faces of the turning piece of the mechanical combination lock is 0.64mm.
5.4.3 The steering blades should have shallow grooves to prevent technical opening. The diameter of the steering blades should generally be different. When the opening numbers of the smuggling regulations are 1.50 divisions between the steering blades, the lock should not be opened.
5.4.4 When the dial of the three-turn steering wheel combination lock rotates beyond the specified opening number of 1.25 divisions, the change of the four-turn steering dial rotation exceeds 1.25 divisions.
5.4.5 The mechanical combination lock rotates 104 times forward and backward, and then opens according to the specified number. The opening number should not change more than 1.25 divisions.
5.4.6 When the mechanical code lock adopts the key to input the code, the key should go through 6000 actions, and there should be no mechanical failure and invalidation of the input code.
5.4.7 The mechanical combination lock should be able to withstand 20 working hours opened by experts or professional technicians by technical means, and the combination lock should not be opened. You can use a computer password to unlock the machine and a detection instrument weighing no more than 22kg.
5.5 Magnetic pin lock 5.5.1 The key of the magnetic pin lock should have a smooth surface and the magnetic material should be firmly installed. The magnetic pin should not fall off under the pressure of 49N.
5.5.2 Magnetic induction strength of the magnetic pin lock After undergoing high temperature, vibration, impact, and drop tests, the decrease in magnetic induction strength should not exceed 10% of the test value before the test.
5.6 Difference, key volume and mutual opening rate 5.6.1 If the length change is used as the difference, the difference shall not be less than 0.5mm, and if the angle change is used as the difference, the difference shall not be less than 15o angle.
In the level of 5.6.2A, the amount of keys for the pin lock should be no less than 6 × 104; the amount of keys for the magnetic pin lock, blade lock, and lever lock should be no less than 2.5 × 104, and the difference exchange number is one.
5.6.3B level, the key quantity of the marble lock should be no less than 3 × 104, and the difference exchange number is two; the key quantity of the magnetic marble lock, blade lock and lever lock should be no less than 1 × 104, The difference exchange number is two.
5.6.4 The theoretical key quantity of the mechanical combination lock of class A should be no less than 1 × 106; the theoretical key quantity of the mechanical combination lock of class B should be no less than 6 × 107 kinds, and the actual amount of keys that can be changed should be Not less than 60% of the theoretical key volume.
5.6.5 For the mechanical anti-theft lock opened with a key, the amount of available keys actually produced should not be less than 40% of the theoretical key.
5.6.6 For mechanical anti-theft locks opened with keys, the mutual opening rate of level B shall not be greater than 0.01%, and the mutual opening rate of level A shall not be greater than 0.03%.
5.7 Flexibility 5.7.1 The mechanical combination lock opened with a key shall have a static pulling force not greater than 9.8N when the key is withdrawn. The key and combination lock dial shall be able to rotate flexibly under the effect of 2Nm torque without blocking.
5.7.2 The axial retracted static pressure of the oblique tongue is not more than 9.8N, and the closed static pressure is not more than 49N.
5.8 Durability requires that the relevant transmission parts of the main lock tongue (bolt) be opened and should be able to be used normally after the following number of cyclic actions. A level: 6 × 104 times B level: 1 × 105 times 5.9 Installation requirements 5.9.1 The structure of the mechanical anti-theft lock should be easy to install, the product must have installation instructions, and the skilled worker should be able to install it correctly according to the technical instructions.
5.9.2 The product structure should ensure that the installation process does not reduce the anti-theft and anti-destructive capabilities of the machine.
5.9.3 The manufacturer shall provide all accessories related to the anti-theft installation of machinery. Special accessories can be agreed with the user by agreement.
5.10 Appearance and dimensions 5.10.1 The clearance between the shoulder of the lock core and the lock body is not more than 0.20mm, the clearance between the lock tongue and the tongue hole is not more than 0.50mm, and the clearance between the lock bolt hole of the combination lock should not be greater than 1.50mm.
5.10.2 After the lock tongue (bolt) is closed, the end surface of the tongue should be flush with the panel, the tolerance should be within ± .05mm, and should not affect the opening of the door. The joint gap between the lock panel and the lock body shell is not more than 0.5mm .
5.10.3 The various rivet parts on the lock body should be firmly connected, the rivet is vertical to the shell, and the rivet head is smooth and flat.
5.10.4 The writing on the dial should be clear, the thickness of the lines should be consistent, and the baseline should be clearly marked.
5.10.5 The surface of the lock ring, external decorative panel, dial, handle, and lock box (board) should be flat and smooth, without cracks, missing corners and obvious scratches.
5.10.6 All metal parts should be selected for chromium plating, nickel plating, zinc plating passivation treatment or paint film coating treatment. 