Wall cracks are more serious problems. Now many new houses have walls with insulation. This kind of wall is prone to wall cracking in the decoration. It must be repaired according to the correct method, otherwise the cracks will come The more serious. The following Xiao Bian gave you a brief introduction to the method of wall crack repair. Causes of wall cracks 1. Cracks in temperature-resilient walls: This type of wall cracking is the most common in walls, mainly due to the transfer of different materials, such as the horizontal cracks at the intersection of ring beams and brick masonry. Such cracks only affect the appearance of the house and will not affect the safety of the house. Some remedial measures can be properly taken: Placing non-woven fabrics at the cracks, installing steel mesh or caulking with mortar, and then painting with paint . 2. The uneven foundation causes cracks in the wall surface of the house: After the house is built, the foundation will generally sink. If the settlement of the foundation is not uniform, relative displacement occurs between the site where the settlement is large and the site where the settlement is small, and shear force and tension are generated in the wall. When the additional internal force exceeds the tensile shear strength of the wall itself, cracks are generated. At the same time, these wall cracks increase as the uneven settlement of the foundation increases. 3. There are errors in the structural design, due to omissions in the calculation of loads, and irrational structures resulting in cracks caused by irrational structures. 4. The construction quality of masonry is poor, the walls are not full of gray when masonry, the thickness is not uniform, and the assembly and installation methods do not meet the requirements. When masonry brick walls, wet bricks are not used, dry bricks are used on walls, etc. Reduce the bearing capacity of masonry, so that the wall will crack later. 5. After the house is built, various pipelines are laid through the wall to destroy the integrity of the wall, reduce the wall surface area, weaken the wall bearing capacity, and cause wall cracks. 6. Change the use of the house, increase the use of load or increase the vibration force, so that the wall is destroyed, causing cracks in the wall. How to repair cracks on the wall 1. Handling grass-roots: In the cracks of the wall, all the walls of the base floor should be cleaned, and a layer of Dacron cloth, kraft paper or newspapers should be applied to the wall surface, and then putty and brush latex paint should be applied. This method is the use of fiber tension, to ensure the integrity of the emulsion paint film, the method is relatively simple and easy. 2. Repair the wall: Remove the insulation board on the surface of the wall, or remove the cement wall. Install a layer of gypsum board or “five board†on the outside of the insulation layer, and then do the latex paint on it. This method is costly and difficult to construct. 3, elastic putty repair: the use of flexible decorative materials. At present, on the method of wall surface treatment, there is a material called elastic putty. This kind of elastic putty can make up for the wall crack problem to a certain extent, and it may not work well on a wall with a relatively large crack. Xiao Bian reminds: If there is a crack in the house of a friend, the appearance of cracks must not be taken lightly. Perhaps the crack is due to the problem of the entire house and there is a crack. Failure to pay attention to the last issue of life safety is not worth the candle! The above is a brief introduction for Xiaobian. If you want to know more related information, please continue to pay attention to Qijia Consulting. More exciting consultation, please stay tuned. Wall cracks living room glass partition wall balcony wall decoration sofa wall background wall wall hanging bookshelf The In-Wall Bidet Frame is a sturdy iron frame specifically designed to provide support for wall-mounted bidets. By fitting into the wall, it effectively conceals the bidet's tank and plumbing, resulting in a modern and streamlined appearance for the bathroom. In Wall Bidet Frame, Wall Hung Bidet Frame, Wall Hung Bidet Holder, In Wall Bidet Holder Guangdong Fabia Intelligent Technology Co., Ltd , https://www.fabiaintelligent.com
Beyond its aesthetic advantages, the in-wall bidet frame offers several functional benefits. One of its primary advantages is the enhanced support it provides for the bidet fixture. This is particularly beneficial for larger individuals or those with limited mobility, as the frame ensures a stable and secure installation. The added support contributes to a comfortable and safe user experience.
The in-wall bidet frame is also height adjustable, allowing for customization to accommodate individual preferences and needs. This feature ensures that users can set the bidet at a comfortable height, promoting optimal usability and convenience.
Moreover, the space-saving design of the in-wall bidet frame is highly advantageous, especially in smaller bathrooms where floor space is limited. By fitting into the wall, the frame eliminates the need for additional floor space, effectively maximizing the available area. This can be particularly valuable for compact bathrooms, as it allows for a more efficient utilization of the available space.
In addition to space-saving benefits, the design of the in-wall bidet frame also facilitates easier cleaning and maintenance. With fewer exposed areas and nooks, there are fewer spaces for dust and grime to accumulate. This simplifies the cleaning process and helps maintain a hygienic environment.